AMERICAN AUDIO V1000 PDF

Posted In Art

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Mukus Togami
Country: Sweden
Language: English (Spanish)
Genre: History
Published (Last): 23 August 2007
Pages: 379
PDF File Size: 2.69 Mb
ePub File Size: 13.61 Mb
ISBN: 230-2-49819-391-3
Downloads: 15296
Price: Free* [*Free Regsitration Required]
Uploader: Molar

If the zmerican ” indicator flashes occasionally, the amplifier is approaching its maximum long-term power capacity. Please do not return the amplifier to your dealer without contacting customer support.

AMERICAN AUDIO V1000 POWER AMP AMPLIFIER 1000 WATTS NR!

The power-supply cord or the plug has been damaged. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector. No user v100 parts inside. A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself.

When dip switches 2 and 3 are in the “ON” the filter will cut off frequencies at and below 30Hz, when these dip switches are in the “OFF” position the americxn will cut off frequencies at and below 50Hz.

Cooling Fan – This breaker is designed to protect the amplifier and your speakers in the event of an AC overload.

Refer all servicing to qualified service personnel.

VLP power amplifier – Amplifier – Audio – Products – ADJ Group

To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another. This fans are used to cool the internal parts of the amplifier when in use. Use your front gain controls to regulate the output volume. The dip switches on the rear panel allows you to configure the low cut filter.

Except for an occasional flash, keep the “CLIP ” indicator dark to avoid overheating the amplifier channel. A limiter takes the gain of an overloading signal and reduces it, the reduction in gain reduces distortion that can cause damage to your speakers and amplifier. Low Cut Frequency Selector When the Low Cut Filter is activated, dip switches 2 channel 1 and 3 channel 2 will control the frequency roll-off.

  EDIMAX EW-7206APG MANUAL PDF

An audik network uncouples RF from the output and helps keep the amplifier stable with reactive loads. Connect your speakers to the outputs on the rear of the amplifier. When the input signal overloads, the “CLIP LED’s” indicate a signal overload, at this time, the master volume should be lowered to reduce distortion. Amplifiers arrive to you preset in the stereo operation mode.

If this line good, check the internal speaker connections and components. To reset the breaker, push it in. Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss amercian bass response.

When connecting your speakers to the amplifier using banana jacks; Be sure that the red americah black caps on the binding post are tighten down completely. Use the channel one gain to regulate your amplifier output. An amplifier’s peak current draw at full output power into 2 ohms is several times what the “normal ” draw is, but its various protection circuits will prevent this condition lasting more than a minute or two.

All channel output during the “Short Circuit Protection” will be interrupted i. Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit. The exclamation point triangular symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the user manual accompanying the amplifier. Antes de usar este amplificador, lea mas advertencias en la guia de operacion.

Before using this amplifier, read the user ahdio for further warnings. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping. It will allow brief clipping of peaks and will only activate when continuous, hard clipping occurs. Cooling Fan – Dual speed a,erican fans. Configuring the Low Cut Filter: The Output Short Circuit V Protection protects the output devices of the amplifier from short circuits and stressful loads.

  COMPRESSIBLE FLOW BY SM YAHYA PDF

American Audio V1000 PLUS Manuals

Dieses Symobl soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen. Connections are made to Channels 1 and 2 output’s for stereo mode or across the red terminals of Channels 1 and 2 for Mono Bridge Mode.

Apply an input source signal to your amplifier. Turn your equipment on your amplifier should always adio the last item you turn on. It’s a community-based project which helps to repair anything. Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding auddio, be sure not to completely remove or unscrew the red and black caps. Auvio unit also provides a way to rear mount the unit into a rack for added security.

Insert the spade connector in to the binding post and tighten the caps down on the spade connector. Never block the fan in any way or mount in an enclose rack, doing so americcan cause the amplifier to overheat and fail.

Cooling Fan Dual speed cooling fans.

Operating instructions AMERICAN AUDIO V PLUS |

This will reduce the use of “Y” cables. This fan is used to cool the internal parts of the amplifier when in use.

Risiko – Elektrischer Schlag! The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground.

Be sure your amplifier and all other audio equipment is powered down. Every Vplus series amplifier has been thoroughly tested V and has been shipped in perfect operating condition. This booklet contains important information concerning the proper and safe operation of your new amplifier.

Connect your speaker across the red output binding post on the rear of your amplifier.