L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked _机械 /仪表_工程科技_专业资料。ASTM A Standard.
|Published (Last):||5 March 2018|
|PDF File Size:||5.86 Mb|
|ePub File Size:||19.12 Mb|
|Price:||Free* [*Free Regsitration Required]|
C Annealed material that naturally meets mechanical properties may be applied. The values obtained in this manner should not, however, be taken as the actual yield strength for 0. HardC Elongation in 2 in.
Only annealed conditions of grades speci? Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. The noncontrolling factor normally will exceed considerably the speci?
Originally approved in B Maximum unless otherwise indicated.
ASTM A Standard Specification for Annealed or Cold-Worked_百度文库
However, in the case of dispute, tests shall be made by pressure. They shall be formed in different shapes such as sheets, strips, plates and flat bars.
Link to Active This link will always route to the current Active version of the standard. The choice of test method for materials in conditions other than annealed shall be at the option of the seller. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions. Rockwell B 95 95 Historical Version s – view previous versions of standard.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
In case of dispute, the offset method of determining yield strength shall be used. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
This standard is subject to revision at any time by the responsible a6666 committee and must be reviewed every? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.
The steels shall adhere to specified chemical composition requirements. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Referenced 6a66 purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Current edition approved Oct.
ASTM-A Alloys | E. Jordan Brookes Company
This revision of Speci? Last previous edition approved in as A — Number of Tests 8. Material Test Report and Certi? A qstm epsilon e indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense. D PSS means plate, strip, sheet.
ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
Specimens shall be bent around a diameter equal to the product of the bend factor times the speci? Hard Elongation in 2 in. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. An alternative method of determining?
astj One bend test shall be made from one end of each coil. The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. This abstract is a brief summary of the referenced standard. A number in parentheses indicates the year of last reapproval.
A — 03 Standard Speci? ICS Number Code B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci? The values given in parentheses are for information only. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The values given in parentheses are for information only.