Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.
|Published (Last):||8 August 2013|
|PDF File Size:||1.99 Mb|
|ePub File Size:||16.5 Mb|
|Price:||Free* [*Free Regsitration Required]|
American Audio V1000 PLUS Manuals
Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of overheating problems. The fixture does not appear to operate normally or exhibits a marked change in performance.
Objects have fallen, or liquid has been spilled into aufio unit. Cooling Fan – Dual speed cooling fans. Below rated output, 8 ohms dB, unweighted dB, unweighted dB, unweighted dB, unweighted dB, unweighted Power Consumption: If the “CLIP ” indicator flashes occasionally, the amplifier is approaching its maximum long-term power capacity. This fan is used to cool the internal parts of the amplifier when in use. Typical speaker output using bare wire.
Operating instructions AMERICAN AUDIO V PLUS |
If it is lit about half the time, the amplifier channel will probably go into v1000 protection within a few minutes. The exclamation point triangular symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the user manual accompanying the amplifier. During low level output the fans run at normal speeds.
P Typical speaker output using spade connectors. Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Turn your equipment on your amplifier should always americann the last item you turn on. If the input gain level is not reduced the built-in limiter will activate. Be sure that your front gain controls are turned down to their lowest level full counter-clockwise.
Use channel two positive output terminal for the negative connection and the channel one positive output terminal for the positive connection.
Refer all servicing to qualified service personnel. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping. Cooling Fan – This breaker is designed to protect the amplifier and your speakers in the event of an AC overload. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector. Dieses Symobl soll den Benutzer auddio wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen.
Insert the spade connector in to the binding post and tighten the caps down on the spade connector.
Red is positive signal and Black is negative signal. The front panel provides four holes used to screw the unit into a rack. Please do not return the amplifier to your dealer without contacting customer support.
American Audio V PLUS Manuals
The dip switches on the rear panel allows you to enable or disable the auudio for each channel, as well as adjust either a 50Hz or 30 Hz cut-off. Except for an occasional flash, keep the “CLIP ” indicator dark to avoid overheating the amplifier channel. Connect your speakers to the outputs on the rear of the amplifier.
The amplifier can operate at practically any power level without risk of overheating. Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.
No user serviceable parts inside.
Operating instructions AMERICAN AUDIO V1000 PLUS
See page 9 for more details on input configuration. At this point channel one will begin to distort. You may also visit us on the web at www. Service Hours are Monday through Friday 9: Risiko – Elektrischer Schlag!