ASTM A/AM: Standard Specification for Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing. A Mechanical Tubing. ASTM A includes steel grades from – Alro stocks A as welded mechanical tubing. A Tube includes a wide. Designation: A – Standard Specification for. Electric-Resistance-Welded Metallic-Coated Carbon Steel Mechanical Tubing1 This standard is issued.
|Published (Last):||10 March 2007|
|PDF File Size:||13.46 Mb|
|ePub File Size:||20.52 Mb|
|Price:||Free* [*Free Regsitration Required]|
The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.
The values stated in either SI units or inch-pound units are to be regarded separately as standard. This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order specifies the applicable M specification designation SI unitsthe inch-pound units shall apply.
Sizes outside the ranges listed above may be ordered provided all other requirements of the specification are met. Combining values from the two systems may result in non-conformance with the standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Low-carbon steels and other carbon steels shall conform to the required chemical composition for zstm, manganese, phosphorus, and sulfur.
A787 Mechanical Tubing
ASTM A Type 3 welded mechanical tubing is produced out of a hot rolled carbon steel and then is hot-dip galvanized per ASTM A specification into a tank of molten zinc after the tubing is already formed and welded.
ASTM A Type 6 welded mechanical tubing is produced using steel that has been pre-coated with a thin layer of a zinc-aluminum-magnesium alloy coating while in coil form as specified in ASTM A This guide covers standard specification for round, square, rectangular, and special shape, electric-resistance-welded mechanical tubing, either zinc-coated galvanized after welding or produced from aluminum-coated, zinc-coated galvanizedzinc-iron alloy-coated galvannealedor aluminum-zinc alloy-coated steel sheet.
Historical Version s – view previous versions of standard. Wall thickness tolerances for premetallic coated as-welded tubing and diameter tolerances for metallic-coated round tubing shall be provided. The steels shall conform to elemental tolerances for product analysis.
This abstract is a brief summary of the referenced standard. We manufacture of ASTM A TYPE 1 Tubingis produced using aluminized steel which is carbon steel that has been pre-coated on both sides with an aluminum silicon alloy while in coil form.
ASTM A Tubing ,ASTM A Type 1,Type 2,Type 3,Type 4,Type 6,ASTM A | Superior Steel
Outside Diameter Tange, in. Within the text, the SI units are shown in brackets.
It is informational only and not an official part of the x787 the full text of the standard itself must be referred to for its use and application.
Within the text, the SI units are shown in brackets.
Link to Active This link will always route to the current Active ast, of the standard. Carbon Steel A Tube Exporter. Combining values from the two systems may result in non-conformance with the standard. A Type 6 Tubing provides a high degree of corrosion resistance and an excellent surface appearance and is a bridge between stainless and hot-dip galvanized finishes. The values stated in either SI units or inch-pound units are to be regarded separately as standard.
A Mechanical Tubing | Alro Steel
ASTM does not a78 any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. ASTM A Type 4 welded mechanical tubing is produced using carbon steel that has been pre-coated with a thin layer of zinc while in coil form and then heat treated a78 convert the coating into a zinc-iron alloy. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other.