BC558C DATASHEET PDF

BCC datasheet, BCC pdf, BCC data sheet, datasheet, data sheet, pdf, Boca Semiconductor Corporation, 30 V, PNP silicon planar epitaxial transistor. BCC Transistor Datasheet pdf, BCC Equivalent. Parameters and Characteristics. BC Silicon PNP Transistor. Audio Amplifier, Switch. Features: D Suitable for AF-Driver Stages and Low Power Output Stages. Absolute Maximum Ratings.

Author: Kemuro Saran
Country: Guinea
Language: English (Spanish)
Genre: Music
Published (Last): 11 January 2014
Pages: 480
PDF File Size: 2.17 Mb
ePub File Size: 17.10 Mb
ISBN: 276-2-50621-234-4
Downloads: 84510
Price: Free* [*Free Regsitration Required]
Uploader: Vigore

BC Pinout, Configuration, Circuit As Switch & Amplifier

For amplification applications, the transistor is biased such that it is partly on for all input conditions. BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that is to be switched.

For switching applications, transistor is biased so that it remains fully on if there is a signal bcc558c its base. When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter. BC is a PNP transistor ratasheet the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin.

  BIBLIA VENDEDOR ALEX DEY PDF

Skip daatsheet main content. The value of this resistor RB can be calculated using below formulae.

BC has a gain value of to ; this value determines the amplification capacity of the transistor. Virgin Galactic — Commercial Space Flight.

The voltage bv558c is the commonly used biasing mode. When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. Complete Technical Details can be found in the BC datasheet given at the end of this page.

Arduino based GPS receiver. Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers. Choosing Battery for Robots. What is Web Browser. TL — Programmable Reference Voltage. A resistor is always added in series with base pin to limit the base current.

The input signal at base is amplified and taken at the emitter. SPI Module of Arduino.

BCC Datasheet(PDF) – Rectron Semiconductor

The DC current gain varies in range to It is also used as a complement for transistors BC to BC Of the above types common emitter type which amplifies dtasheet is the popular and mostly used configuration.

Interface SD Card with Arduino. Amplifier modules like Audio amplifiers, signal Amplifier etc. Choosing Motor For Robots. Submitted by admin on 26 March A Transistors acts as eatasheet Amplifier when operating in Active Region.

The BC because of this large gain value is normally used to as a audio amplifier.

  DECRETO 52054 PDF

It can amplify power, voltage and current at different configurations. This is known as the biasing. BC is a general purpose PNP transistor. In the absence of base signal, it gets completely off. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around gc558c.

When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal.

BC558C Datasheet, Equivalent, Cross Reference Search

It is used in switching and amplifier applications. Interface GPS with Arduino. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base datashest. This high-density System-in-Package SiP integrates controller, power switches, and support components. BC is used in common emitter configuration for amplifiers.

The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves.